Meyer Sound ULTRA-X20 Speaker and USW-112P Subwoofer Pair Package
The PA-PACK-1484 package contains the following items:
*2x Meyer Sound ULTRA-X20 Self-Powered Full-Range Loudspeaker with 3-Pin XLR
Meyer Sound’s ULTRA-X20™ design extends the award-winning, state-of-the-art ULTRA-X40™ point source technology to a smaller version for size- and weight-critical applications. The ULTRA-X20 loudspeaker provides high power output, low distortion, and consistent polar response in a very compact, vented enclosure. The loudspeaker features two 5-inch cone low-frequency drivers and one 2-inch diaphragm compression driver coupled with a rotatable 110° x 50° constant-Q horn.
Features:
- A compact, elegant and light aluminum enclosure encases exceptional fidelity and surprising power capability
- Extraordinarily flat amplitude and phase response ensures tonal accuracy and precise imaging
- Wide pattern covers broad listening areas
- Rotatable horn provides installation flexibility
- Integral stand mount and QuickFly® mounting options facilitate rigging
Specifications:
- Acoustical:
- Operating Frequency Range: 60 Hz – 18 kHz
- Frequency Response: 65 Hz – 17.5 kHz ± 4 dB
- Phase Response: 95 Hz – 18 kHz ±45°
- Linear Peak SPL: 127 dB with 20 dB crest factor (M-noise), 123.5 dB (Pink Noise), 125.5 dB (B-noise)
- Coverage:
- Rotatable horn: 110° x 50°
- Crossover: 830 Hz
- Transducers:
- Low Frequency: Two 5-inch cone drivers; 6 Ω nominal impedance
- High Frequency: One 2-inch diaphragm compression driver connected to a rotatable horn; 8 Ω nominal impedance
- Audio Input:
- Analog Audion Version:
- Type: Differential, electronically balanced
- Maximum Common Mode Range: ±15 V DC, clamped to earth for voltage transient protection
- Connectors: XLR 3-pin female input with male loop output.
- Input Impedance: 10 kΩ differential between pins 2 and 3
- Wiring:
- Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
- Pin 2: Signal +
- Pin 3: Signal -
- Case: Earth ground and chassis
- Nominal Input Sensitivity: 0.0 dBV (1.0 V rms) continuous is typically the onset of limiting for noise and music
- Input Level: Audio source must be capable of producing +20 dBV (10 V rms, 14 V peak) into 600 oms to produce the maximum peak SPL over the operating bandwidth of the loudspeaker
- Amplifier:
- Type: Three-channel, Class-D
- Total Output Power: 860 W peak
- THD, IM, TIM: < 0.02%
- Cooling: Convection
- AC Power:
- Connectors: powerCON 20 input with loop output; powerCON TRUE1 TOP with loop output on digital and weather-protected units
- Automatic Voltage Selection: 90–265 V AC, 50–60 Hz
- Safety Rated Voltage Range: 100–240 V AC, 50–60 Hz
- Turn-on and Turn-off Points: 90 V AC turn-on, no turn-off; internal fuse protection above 265 V AC
- Current Draw:
- Idle Current: 0.15 A rms (115 V AC); 0.13 A rms (230 V AC); 0.16 A rms (100 V AC)
- Maximum Long-Term Continuous Current (>10 sec): 0.9 A rms (115 V AC); 0.5 A rms (230 V AC); 1.1 A rms (100 V AC)
- Burst Current (<1 sec): 1.6 A rms (115 V AC); 0.8 A rms (230 V AC); 1.8 A rms (100 V AC)
- Maximum Instantaneous Peak Current: 3.5 A peak (115 V AC); 1.8 A peak (230 V AC); 4.1 A peak (100 V AC)
- Inrush Current: < 20 A peak
- Physical:
- Dimensions: W: 7.44 in (189 mm) x H: 19.04 in (484 mm) x D: 8.66 in (220 mm)
- Weight: 27 lb (12.3 kg)
- Enclosure: Aluminum with slightly textured black finish
- Two integrated M8 threaded points on each end; optional accessories for various rigging options (see accessories section); four M6 threaded holes with 5-inch by 2.75-inch (127 mm by 70 mm) hole pattern on the rear for use with third-party wall mounts.
- Protective Grille: Powder-coated, round-perforated steel
*2x Meyer Sound USW-112P Self-Powered Subwoofer with 3-Pin XLR
- Acoustical:
- Operating Frequency Range: 60 Hz – 18 kHz
- Frequency Response: 65 Hz – 17.5 kHz ± 4 dB
- Phase Response: 95 Hz – 18 kHz ±45°
- Linear Peak SPL: 127 dB with 20 dB crest factor (M-noise), 123.5 dB (Pink Noise), 125.5 dB (B-noise)
- Coverage:
- Rotatable horn: 110° x 50°
- Crossover: 830 Hz
- Transducers:
- Low Frequency: Two 5-inch cone drivers; 6 Ω nominal impedance
- High Frequency: One 2-inch diaphragm compression driver connected to a rotatable horn; 8 Ω nominal impedance
- Audio Input:
- Analog Audion Version:
- Type: Differential, electronically balanced
- Maximum Common Mode Range: ±15 V DC, clamped to earth for voltage transient protection
- Connectors: XLR 3-pin female input with male loop output.
- Input Impedance: 10 kΩ differential between pins 2 and 3
- Wiring:
- Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
- Pin 2: Signal +
- Pin 3: Signal -
- Case: Earth ground and chassis
- Nominal Input Sensitivity: 0.0 dBV (1.0 V rms) continuous is typically the onset of limiting for noise and music
- Input Level: Audio source must be capable of producing +20 dBV (10 V rms, 14 V peak) into 600 oms to produce the maximum peak SPL over the operating bandwidth of the loudspeaker
- Analog Audion Version:
- Amplifier:
- Type: Three-channel, Class-D
- Total Output Power: 860 W peak
- THD, IM, TIM: < 0.02%
- Cooling: Convection
- AC Power:
- Connectors: powerCON 20 input with loop output; powerCON TRUE1 TOP with loop output on digital and weather-protected units
- Automatic Voltage Selection: 90–265 V AC, 50–60 Hz
- Safety Rated Voltage Range: 100–240 V AC, 50–60 Hz
- Turn-on and Turn-off Points: 90 V AC turn-on, no turn-off; internal fuse protection above 265 V AC
- Current Draw:
- Idle Current: 0.15 A rms (115 V AC); 0.13 A rms (230 V AC); 0.16 A rms (100 V AC)
- Maximum Long-Term Continuous Current (>10 sec): 0.9 A rms (115 V AC); 0.5 A rms (230 V AC); 1.1 A rms (100 V AC)
- Burst Current (<1 sec): 1.6 A rms (115 V AC); 0.8 A rms (230 V AC); 1.8 A rms (100 V AC)
- Maximum Instantaneous Peak Current: 3.5 A peak (115 V AC); 1.8 A peak (230 V AC); 4.1 A peak (100 V AC)
- Inrush Current: < 20 A peak
- Physical:
- Dimensions: W: 7.44 in (189 mm) x H: 19.04 in (484 mm) x D: 8.66 in (220 mm)
- Weight: 27 lb (12.3 kg)
- Enclosure: Aluminum with slightly textured black finish
- Two integrated M8 threaded points on each end; optional accessories for various rigging options (see accessories section); four M6 threaded holes with 5-inch by 2.75-inch (127 mm by 70 mm) hole pattern on the rear for use with third-party wall mounts.
- Protective Grille: Powder-coated, round-perforated steel
*2x Meyer Sound USW-112P Self-Powered Subwoofer with 3-Pin XLR
The USW-112P compact narrow subwoofer provides big bass sound for very tight spaces. Its compact rectangular enclosure and slanted connector panel enable flush-mounting of the cabinet against wall surfaces, reducing required installation depth to 12 inches, including connectors. Designed to be the ideal companion to Meyer Sound’s ULTRA-X20, it also complements the low frequencies in other Meyer Sound loudspeakers, such as the UP-4slim and those in the UPM family. The USW-112P has an operating frequency range of 35–140 Hz with a linear peak SPL of 123 dB, measured in half-space at 4 m and referred to 1 m using M-noise. The bass reflex cabinet employs a low-velocity port design for high efficiency and low port distortion.
Specifications:
- Acoustical:
- Operating Frequency Range: 35 Hz – 140 Hz
- Frequency Response: 36 Hz – 125 Hz ± 4 dB
- Phase Response: 45 Hz – 120 Hz ±30°
- Linear Peak SPL: 123 dB with > 10.5 dB crest factor (M-noise), 123 dB (Pink Noise), 125 dB (B-noise)
- Transducers:
- Low Frequency: One 12-inch cone driver; 3 Ω nominal impedance
- Audio Input:
- Type: Differential, electronically balanced
- Maximum Common Mode Range: ±15 V DC, clamped to earth for voltage transient protection
- Connectors:
- Analog Audio Version: XLR 3-pin female input with male loop output.
- Input Impedance: 10 kΩ differential between Audio(+) and Audio(-)
- Wiring:
- Pin 1: Chassis/earth through 1 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
- Pin 2: Signal +
- Pin 3: Signal -
- Case: Earth ground and chassis
- Nominal Input Sensitivity: 0 dBV (1.0 V rms) continuous is typically the onset of limiting for noise and music
- Input Level: Audio source must be capable of producing of +20 dBV (10 V rms) into 600 Ω to produce the maximum peak SPL over the operating bandwidth of the loudspeaker.
- Amplifier:
- Type: Open-loop, Class-D
- Total Output Power: 1200 W peak
- THD, IM, TIM: < 0.02%
- Cooling: Convection
- AC Power:
- Connectors: powerCON 20 input with loop output; powerCON TRUE1 TOP with loop output on digital and weather-protected units
- Automatic Voltage Selection: 90–265 V AC, 50–60 Hz
- Safety Rated Voltage Range: 100–240 V AC, 50–60 Hz
- Turn-on and Turn-off Points: 90 V AC turn-on, no turn-off; internal fuse protection above 265 V AC
- Current Draw:
- Idle Current: 0.23 A rms (115 V AC); 0.18 A rms (230 V AC); 0.25 A rms (100 V AC)
- Maximum Long-Term Continuous Current (>10 sec): 1.2 A rms (115 V AC); 0.7 A rms (230 V AC); 1.4 A rms (100 V AC)
- Burst Current (<1 sec): 3.6 A rms (115 V AC); 1.8 A rms (230 V AC); 4.1 A rms (100 V AC)
- Maximum Instantaneous Peak Current: 8.9 A peak (115 V AC); 4.5 A peak (230 V AC); 10.3 A peak (100 V AC)
- Inrush Current: < 20 A peak
- Physical:
- Dimensions: W: 13.5 in (343 mm) x H: 23.5 in (597 mm) x D: 12 in (305 mm)
- Weight: 45 lb (20 kg)
- Enclosure: Premium multi-ply birch with slightly textured black finish
- IP Rating: Weather-protected version rated IP54
- Protective Grille: Powder-coated, round-perforated steel
- Rigging: Two integrated M8 threaded points; 35 mm Pole Mount with M20 thread; optional U-bracket for wall, ceiling, or truss mounting
*2x Meyer Sound MPK-POLE 35–38mm Pneumatic Speaker Pole
- Operating Frequency Range: 35 Hz – 140 Hz
- Frequency Response: 36 Hz – 125 Hz ± 4 dB
- Phase Response: 45 Hz – 120 Hz ±30°
- Linear Peak SPL: 123 dB with > 10.5 dB crest factor (M-noise), 123 dB (Pink Noise), 125 dB (B-noise)
- Low Frequency: One 12-inch cone driver; 3 Ω nominal impedance
- Type: Differential, electronically balanced
- Maximum Common Mode Range: ±15 V DC, clamped to earth for voltage transient protection
- Connectors:
- Analog Audio Version: XLR 3-pin female input with male loop output.
- Input Impedance: 10 kΩ differential between Audio(+) and Audio(-)
- Wiring:
- Pin 1: Chassis/earth through 1 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
- Pin 2: Signal +
- Pin 3: Signal -
- Case: Earth ground and chassis
- Nominal Input Sensitivity: 0 dBV (1.0 V rms) continuous is typically the onset of limiting for noise and music
- Input Level: Audio source must be capable of producing of +20 dBV (10 V rms) into 600 Ω to produce the maximum peak SPL over the operating bandwidth of the loudspeaker.
- Type: Open-loop, Class-D
- Total Output Power: 1200 W peak
- THD, IM, TIM: < 0.02%
- Cooling: Convection
- Connectors: powerCON 20 input with loop output; powerCON TRUE1 TOP with loop output on digital and weather-protected units
- Automatic Voltage Selection: 90–265 V AC, 50–60 Hz
- Safety Rated Voltage Range: 100–240 V AC, 50–60 Hz
- Turn-on and Turn-off Points: 90 V AC turn-on, no turn-off; internal fuse protection above 265 V AC
- Idle Current: 0.23 A rms (115 V AC); 0.18 A rms (230 V AC); 0.25 A rms (100 V AC)
- Maximum Long-Term Continuous Current (>10 sec): 1.2 A rms (115 V AC); 0.7 A rms (230 V AC); 1.4 A rms (100 V AC)
- Burst Current (<1 sec): 3.6 A rms (115 V AC); 1.8 A rms (230 V AC); 4.1 A rms (100 V AC)
- Maximum Instantaneous Peak Current: 8.9 A peak (115 V AC); 4.5 A peak (230 V AC); 10.3 A peak (100 V AC)
- Inrush Current: < 20 A peak
- Dimensions: W: 13.5 in (343 mm) x H: 23.5 in (597 mm) x D: 12 in (305 mm)
- Weight: 45 lb (20 kg)
- Enclosure: Premium multi-ply birch with slightly textured black finish
- IP Rating: Weather-protected version rated IP54
- Protective Grille: Powder-coated, round-perforated steel
- Rigging: Two integrated M8 threaded points; 35 mm Pole Mount with M20 thread; optional U-bracket for wall, ceiling, or truss mounting
Adjustable length 927–1524 mm (36.5–60 in) pole with assisted lift. Lower shaft fits 35 mm cups or use the removable M20 threaded lug for added stability. Upper shaft includes a PAS-M20 Adapter Sleeve to fit loudspeakers with 35 mm and M20 internal pole mounts onto a 35 mm speaker stand. (Can also buy the PAS-M20 Adapter Sleeve separately). Additional 35 mm to 38 mm (1.5 in) adapter and PAS-M8 Adapter Sleeve included.
