Meyer Sound ULTRA-X22 Self-Powered Full-Range Loudspeaker with 3-Pin XLR
Meyer Sound’s ULTRA-X22™ design extends the award-winning, state-of-the-art ULTRA-X40™ point source technology to a smaller version for size- and weight-critical applications. The ULTRA-X22 loudspeaker provides high power output, low distortion, and consistent polar response in a very compact, vented enclosure. The loudspeaker features two 5-inch cone low-frequency drivers and one 2-inch diaphragm compression driver coupled with a rotatable 80° x 50° constant-Q horn.
Features:
- A compact, elegant and light aluminum enclosure encases exceptional fidelity and surprising power capability
- Extraordinarily flat amplitude and phase response ensures tonal accuracy and precise imaging
- Wide pattern covers broad listening areas
- Rotatable horn provides installation flexibility
- Integral stand mount and QuickFly® mounting options facilitate rigging
Specifications:
- Acoustical:
- Operating Frequency Range:60 Hz – 18 kHz
- Frequency Response: 65 Hz – 17.5 kHz ± 4 dB
- Phase Response: 95 Hz – 18 kHz ±45°
- Linear Peak SPL: 128.5 dB with 20 dB crest factor (M-noise), 123.5 dB (Pink Noise), 125 dB (B-noise)
- Coverage:
- Rotatable horn: 80° x 50°
- Crossover: 830 Hz
- Transducers:
- Low Frequency: Two 5-inch cone drivers; 6 Ω nominal impedance
- High Frequency: One 2-inch diaphragm compression driver connected to a rotatable horn; 8 Ω nominal impedance
- Audio Input:
- Analog Audion Version:
- Type: Differential, electronically balanced
- Maximum Common Mode Range: ±15 V DC, clamped to earth for voltage transient protection
- Connectors: XLR 3-pin female input with male loop output.
- Input Impedance: 10 kΩ differential between pins 2 and 3
- Wiring:
- Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
- Pin 2: Signal +
- Pin 3: Signal -
- Case: Earth ground and chassis
- Nominal Input Sensitivity: 0.0 dBV (1.0 V rms) continuous is typically the onset of limiting for noise and music
- Input Level: Audio source must be capable of producing +20 dBV (10 V rms, 14 V peak) into 600 oms to produce the maximum peak SPL over the operating bandwidth of the loudspeaker
- Amplifier:
- Type: Three-channel, Class-D
- Total Output Power: 860 W peak
- THD, IM, TIM: < 0.02%
- Cooling: Convection
- AC Power:
- Connectors: powerCON 20 input with loop output; powerCON TRUE1 TOP with loop output on digital and weather-protected units
- Automatic Voltage Selection: 90–265 V AC, 50–60 Hz
- Safety Rated Voltage Range: 100–240 V AC, 50–60 Hz
- Turn-on and Turn-off Points: 90 V AC turn-on, no turn-off; internal fuse protection above 265 V AC
- Current Draw:
- Idle Current: 0.15 A rms (115 V AC); 0.13 A rms (230 V AC); 0.16 A rms (100 V AC)
- Maximum Long-Term Continuous Current (>10 sec): 0.9 A rms (115 V AC); 0.5 A rms (230 V AC); 1.1 A rms (100 V AC)
- Burst Current (<1 sec): 1.6 A rms (115 V AC); 0.8 A rms (230 V AC); 1.8 A rms (100 V AC)
- Maximum Instantaneous Peak Current: 3.5 A peak (115 V AC); 1.8 A peak (230 V AC); 4.1 A peak (100 V AC)
- Inrush Current: < 20 A peak
- Physical:
- Dimensions: W: 7.44 in (189 mm) x H: 19.04 in (484 mm) x D: 8.66 in (220 mm)
- Weight: 27 lb (12.3 kg)
- Enclosure: Aluminum with slightly textured black finish
- Two integrated M8 threaded points on each end; optional accessories for various rigging options (see accessories section); four M6 threaded holes with 5-inch by 2.75-inch (127 mm by 70 mm) hole pattern on the rear for use with third-party wall mounts.
- Protective Grille: Powder-coated, round-perforated steel
