Meyer Sound ULTRA-X22 Self-Powered Full-Range Weather Protected Loudspeaker with 3-Pin XLR
Meyer Sound’s ULTRA-X22™ design extends the award-winning, state-of-the-art ULTRA-X40™ point source technology to a smaller version for size- and weight-critical applications. The ULTRA-X22 loudspeaker provides high power output, low distortion, and consistent polar response in a very compact, vented enclosure. The loudspeaker features two 5-inch cone low-frequency drivers and one 2-inch diaphragm compression driver coupled with a rotatable 80° x 50° constant-Q horn.
Features:
- A compact, elegant and light aluminum enclosure encases exceptional fidelity and surprising power capability
- Extraordinarily flat amplitude and phase response ensures tonal accuracy and precise imaging
- Wide pattern covers broad listening areas
- Rotatable horn provides installation flexibility
- Integral stand mount and QuickFly® mounting options facilitate rigging
Specifications:
- Acoustical:
- Operating Frequency Range:60 Hz – 18 kHz
- Frequency Response: 65 Hz – 17.5 kHz ± 4 dB
- Phase Response: 95 Hz – 18 kHz ±45°
- Linear Peak SPL: 128.5 dB with 20 dB crest factor (M-noise), 123.5 dB (Pink Noise), 125 dB (B-noise)
- Coverage:
- Rotatable horn: 80° x 50°
- Crossover: 830 Hz
- Transducers:
- Low Frequency: Two 5-inch cone drivers; 6 Ω nominal impedance
- High Frequency: One 2-inch diaphragm compression driver connected to a rotatable horn; 8 Ω nominal impedance
- Audio Input:
- Analog Audion Version:
- Type: Differential, electronically balanced
- Maximum Common Mode Range: ±15 V DC, clamped to earth for voltage transient protection
- Connectors: XLR 3-pin female input with male loop output; XLR 3-pin TOP (Total Outdoor Protection) connectors on weather-protected units only.
- Input Impedance: 10 kΩ differential between pins 2 and 3
- Wiring:
- Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
- Pin 2: Signal +
- Pin 3: Signal -
- Nominal Input Sensitivity: 0.0 dBV (1.0 V rms) continuous is typically the onset of limiting for noise and music
- Input Level: Audio source must be capable of producing +20 dBV (10 V rms, 14 V peak) into 600 oms to produce the maximum peak SPL over the operating bandwidth of the loudspeaker
- Amplifier:
- Type: Three-channel, Class-D
- Total Output Power: 860 W peak
- THD, IM, TIM: < 0.02%
- Cooling: Convection
- AC Power:
- Connectors: powerCON 20 input with loop output; powerCON TRUE1 TOP with loop output on digital and weather-protected units
- Automatic Voltage Selection: 90–265 V AC, 50–60 Hz
- Safety Rated Voltage Range: 100–240 V AC, 50–60 Hz
- Turn-on and Turn-off Points: 90 V AC turn-on, no turn-off; internal fuse protection above 265 V AC
- Current Draw:
- Idle Current: 0.15 A rms (115 V AC); 0.13 A rms (230 V AC); 0.16 A rms (100 V AC)
- Maximum Long-Term Continuous Current (>10 sec): 0.9 A rms (115 V AC); 0.5 A rms (230 V AC); 1.1 A rms (100 V AC)
- Burst Current (<1 sec): 1.6 A rms (115 V AC); 0.8 A rms (230 V AC); 1.8 A rms (100 V AC)
- Maximum Instantaneous Peak Current: 3.5 A peak (115 V AC); 1.8 A peak (230 V AC); 4.1 A peak (100 V AC)
- Inrush Current: < 20 A peak
- Physical:
- Dimensions: W: 7.44 in (189 mm) x H: 19.04 in (484 mm) x D: 8.66 in (220 mm)
- Weight: 27 lb (12.3 kg)
- Enclosure: Aluminum with slightly textured black finish
- IP Rating: Weather-protected version rated IP54.
- Two integrated M8 threaded points on each end; optional accessories for various rigging options (see accessories section); four M6 threaded holes with 5-inch by 2.75-inch (127 mm by 70 mm) hole pattern on the rear for use with third-party wall mounts.
- Protective Grille: Powder-coated, round-perforated steel
MEYER SOUND WEATHER PROTECTION
The Weather Protection option from Meyer Sound is intended to increase the useful life of Meyer Sound loudspeakers when they are installed outdoors and exposed to different and often harsh weather conditions. Meyer Sound Weather Protection includes a penetrating treatment to raw wood, use of special primers, and plating on all steel parts used (or alternatively, the use of stainless steel hardware). Weather Protection is designed to prevent malfunctions caused by harsh operating environments and slows the accelerated wear and tear that occurs in outdoor environments.
