Name: Crestron GL-EXP-DIMU-CN Green Light Universal Dimmer Expansion Module for Cresnet Communications
Brand: Crestron Electronics
SKU: TZ-GL-EXP-DIMU-CN
Price: 59.99 USD
Availability: InStock

Description

Crestron GL-EXP-DIMU-CN Green Light Universal Dimmer Expansion Module for Cresnet Communications

The GL-EXP-DIMU-CN is a single-channel universal dimmer expansion module that allows for added lighting zones without an additional cabinet install. The expansion module controls electronic and magnetic low-voltage, LED, incandescent, and 2- wire fluorescent loads. Utilizing proprietary zero-cross filter technology, the GL-EXP-DIMU-CN compensates for line voltage and frequency fluctuations to provide immunity to power line noise and a dramatic reduction in lamp flicker.

Auto-Detecting Universal Dimming: Under normal operation, the GL-EXP-DIMU-CN detects the connected load type and selects the appropriate operating mode automatically. Reverse phase (trailing edge) mode supports incandescent and electronic low-voltage load types, while forward phase (leading edge) mode handles magnetic low-voltage and other inductive load types. Center phase mode is also available, combining reverse and forward phase load control to address special cases. The operative mode is indicated by two LEDs located on the front panel.

Cresnet® Communications: The GL-EXP-DIMU-CN interfaces with a Crestron control system via Cresnet. Cresnet is a simple 4-wire network bus that provides the communications backbone for a system of Crestron lighting dimmers, switches, keypads, shades, thermostats, and other devices.

Emergency Lighting Control: The GL-EXP-DIMU-CN is UL® 924 listed for use in controlling an emergency lighting load. In the event of a power failure, a contact closure from a power loss sensor (GLS-PLS-120/277, sold separately) activates the override mode in the GL-EXPDIMU-CN to turn on the lighting load if it is off (assuming line power is supplied by a backup power source). The override dimming level can be preset to any value when commissioning the lighting system, so even if the load is already on prior to a power failure, it will change to the preset level when override mode is activated.

Plenum Rated NEMA Enclosure: The GL-EXP-DIMU-CN is designed to be mounted to a vertical surface and is UL 2043 compliant to allow for installation in an environmental air-handling space above a suspended ceiling. Conduit knockouts are provided on the bottom and lower sides of the unit. All connections are made via screw terminals behind the front cover.

Single-channel universal lighting dimmer
Crestron® system integration via Cresnet® communications
Supports dimmable LED, incandescent, electronic low-voltage, magnetic low-voltage, and 2-wire fluorescent lighting loads
Rated 16 A at 100-277 VAC
Auto load type detection
Forward and reverse phase modes
Zero-cross filter technology for reduced lamp flicker
Extreme stability under noisy power line conditions
Built-in air gap relay
Closure-activated override mode
UL® 924 listed for emergency lighting control
Surface mountable NEMA Type 1 enclosure
Mounts on a wall panel or above a suspended ceiling
UL 2043 listed for installation in an environmental air handling space

Specifications

Load Control

Dimmer Channels: 1
Load Rating: 16 A
Line Voltage: 100-277 VAC, 50/60 Hz
Dimmable Load Types: Incandescent, LED, electronic low-voltage, magnetic low-voltage, 2-wire fluorescent

Communications

Cresnet : Cresnet slave mode

Connections

NEUT: (3) Captive screw terminals; Neutral connections for feed and load; 24 to 10 AWG (0.25 to 4.0 mm²) wire size
LINE: (2) Captive screw terminals; Line power feed input and pass-through; 24 to 10 AWG (0.25 to 4.0 mm²) wire size
DIM: (1) Captive screw terminal; Dimmed load output; 24 to 10 AWG (0.25 to 4.0 mm²) wire size
OVERRIDE:

(2) Captive screw terminals; Low-voltage contact closure sensing input; Activates override mode when a closure is sensed;
26 to 14 AWG (0.14 to 1.5 mm²) wire size; For use with Class 2 wiring only

CRESNET:

(4) Captive screw terminals; Cresnet slave port (communications only, does not use Cresnet power);
26 to 14 AWG (0.14 to 1.5 mm²) wire size; For use with Class 2 wiring only

Ground: (1) 3-terminal grounding block

Controls and Indicators

PWR : (1) Green LED, indicates line power is applied to either LINE terminal
NET: (1) Yellow LED, indicates Cresnet network communication
ERR: (1) Red LED, indicates a variety of error conditions via blinking patterns (refer to the installation guide)
ON/OFF: (1) Pushbutton and (1) red LED, pushbutton toggles the load output on and off (press and hold to cycle the dimming level up and down), LED indicates the load output is energized
FWD: (1) Red LED, indicates forward phase mode (or center phase mode if REV indicator is also on)
REV: (1) Red LED, indicates reverse phase mode (or center phase mode if FWD indicator is also on)
RESET: (1) Pushbutton, initiates hardware reset
SW1: (1) Two-position slide switch (behind front cover), enables/disables the zero-cross detection filter (disabled by default)
SW2: (1) Two-position slide switch (behind front cover), not used
SW3, SW4: (2) Two-position slide switches (behind front cover); selects auto detect (default), forward phase, reverse phase, or center phase dimming mode

Environmental

Temperature: 32° to 104° F (0° to 40° C)
Humidity: 10% to 90% RH (noncondensing)

Construction

Enclosure: NEMA Type 1, galvanized steel with gray matte powder coated removable front cover panel, extruded aluminum heat sink on rear, (2) integral mounting flanges, (4) 0.5 in. (13 mm) or 0.75 in. (19 mm) conduit knockouts on bottom and lower left & right sides
Mounting: Surface mount, must be oriented upright and mounted to a vertical surface with 6 in. (153 mm) minimum spacing above and below for proper ventilation and heat dissipation