Meyer Sound UPA-2P Self-Powered Loudspeaker
The Meyer UPA-P Series self-powered loudspeakers (UPA-1P,UPA-2P) are more than powered versions of the Meyer UPA-C Series (UPA-1C, UPA-2C). The UPA-P Series features phase-corrected electronics that produce flat acoustical phase and amplitude responses, resulting in exceptional system impulse response and precise imaging. Despite the inclusion of amplification and control electronics, the UPA-P is the same size as, and only 10 lb.heavier than the UPA-C. Additionally, the UPA-P’s advanced horn designs achieve a consistent polar response and smooth arraying behavior.
Features:
- Exceptional fidelity and extended high- frequency performance
- Surprising power capability in a compact package
- Extraordinarily flat amplitude and phase response for tonal accuracy and precise imaging
- Constant-Q horn affords uniform response throughout the coverage area
- Narrow pattern enables precisely controlled coverage and arrayability and increases efficency at high frequencies
- Predictable array performance ensures system design flexibility
- Symmetrical horn allows loudspeakers to be oriented horizontally or vertically
Specifications:
- ACOUSTICAL
- Operating Frequency Range: 60 Hz - 18 kHz
- Frequency Response: 80 Hz - 17 kHz ±4 dB
- Phase Response: 600 Hz - 16 kHz ±35°
- Linear Peak SPL: 132.5 dB (M-noise), 132 dB (Pink noise), 136 dB (B-noise)
- COVERAGE
- Horizontal Coverage: 45°
- Vertical Coverage: 45°
- TRANSDUCERS
- Low Frequency: One 12 in cone driver; 2 Ω nominal impedance
- High Frequency: One 3 in compression driver; 16 Ω nominal impedance
- AUDIO INPUT
- Type: Differential, electronically balanced
- Maximum Common Mode Range: ±15 V DC, clamped to earth for voltage transient protection
- Connectors: XLR 3 female input with male loop output; optional XLR 5-pin connectors to accommodate both balanced audio and RMS signals.
- Input Impedance: 10 kΩ differential between pins 2 and 3
- Wiring:
- Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
- Pin 2: Signal +
- Pin 3: Signal - (optional polarity reversal switch)
- Case: Earth ground and chassis
- Nominal Input Sensitivity: 0 dBV (1.0 V rms) continuous is typically the onset of limiting for noise and music
- Input Level: Audio source must be capable of producing of +20 dBV (10 V rms) into 600 Ω to produce the maximum peak SPL over the operating bandwidth of the loudspeaker.
- AMPLIFIER
- Type: Two-channel complementary MOSFET output stages (class AB/bridged)
- Total Output Power: 1000 W peak
- THD, IM, TIM: < 0.02%
- Cooling
- Convection; 24 V DC output for optional external fan
- AC POWER
- Connector: PowerCON20 input
- Automatic Voltage Selection: 90–265 V AC
- Safety Rated Voltage Range: 100–240 V AC, 50–60 Hz
- Turn-on and Turn-off Points: 90 V AC turn-on, no turn-off; internal fuse-protection above 265 V AC
- CURRENT DRAW
- Idle Current: 0.25 A rms (115 V AC); 0.13 A rms (230 V AC); 0.3 A rms (100 V AC)
- Maximum Long-Term Continuous Current (>10 sec): 2.8 A rms (115 V AC); 1.4 A rms (230 V AC); 3.2 A rms (100 V AC)
- Burst Current (<1 sec): 3.2 A rms (115 V AC); 1.6 A rms (230 V AC); 3.7 A rms (100 V AC)
- Maximum Instantaneous Peak Current: 5.0 A pk (115 V AC); 2.5 A pk (230 V AC); 5.8 A pk (100 V AC)
- Inrush Current: < 9 A peak (115 V AC and 230 V AC)
- RMS NETWORK (OPTIONAL)
- Equipped with two-conductor twisted-pair network, reporting all operating parameters of amplifiers to system operator’s host computer.
- PHYSICAL
- Dimensions: W: 14.50 in (368 mm) x H: 22.40 in (569 mm) x D: 14.30 in (363 mm)
- Weight: 77 lb (34.93 kg)
- Enclosure: Premium multi-ply birch with slightly textured black finish
- Protective Grille: Powder-coated, hex-stamped steel with black mesh covering
- Rigging:
- Four ring and stud pan fittings, two on both top and bottom. Working load for each fitting is 420 lbs (190.51 kg), 1/5 the cabinet breaking strength (with straight tensile pull); 3/8 in or metric M10 nut plates optional
- ACOUSTICAL
- Operating Frequency Range: 60 Hz - 18 kHz
- Frequency Response: 80 Hz - 17 kHz ±4 dB
- Phase Response: 600 Hz - 16 kHz ±35°
- Linear Peak SPL: 132.5 dB (M-noise), 132 dB (Pink noise), 136 dB (B-noise)
- COVERAGE
- Horizontal Coverage: 45°
- Vertical Coverage: 45°
- TRANSDUCERS
- Low Frequency: One 12 in cone driver; 2 Ω nominal impedance
- High Frequency: One 3 in compression driver; 16 Ω nominal impedance
- AUDIO INPUT
- Type: Differential, electronically balanced
- Maximum Common Mode Range: ±15 V DC, clamped to earth for voltage transient protection
- Connectors: XLR 3 female input with male loop output; optional XLR 5-pin connectors to accommodate both balanced audio and RMS signals.
- Input Impedance: 10 kΩ differential between pins 2 and 3
- Wiring:
- Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
- Pin 2: Signal +
- Pin 3: Signal - (optional polarity reversal switch)
- Case: Earth ground and chassis
- Nominal Input Sensitivity: 0 dBV (1.0 V rms) continuous is typically the onset of limiting for noise and music
- Input Level: Audio source must be capable of producing of +20 dBV (10 V rms) into 600 Ω to produce the maximum peak SPL over the operating bandwidth of the loudspeaker.
- AMPLIFIER
- Type: Two-channel complementary MOSFET output stages (class AB/bridged)
- Total Output Power: 1000 W peak
- THD, IM, TIM: < 0.02%
- Cooling
- Convection; 24 V DC output for optional external fan
- AC POWER
- Connector: PowerCON20 input
- Automatic Voltage Selection: 90–265 V AC
- Safety Rated Voltage Range: 100–240 V AC, 50–60 Hz
- Turn-on and Turn-off Points: 90 V AC turn-on, no turn-off; internal fuse-protection above 265 V AC
- CURRENT DRAW
- Idle Current: 0.25 A rms (115 V AC); 0.13 A rms (230 V AC); 0.3 A rms (100 V AC)
- Maximum Long-Term Continuous Current (>10 sec): 2.8 A rms (115 V AC); 1.4 A rms (230 V AC); 3.2 A rms (100 V AC)
- Burst Current (<1 sec): 3.2 A rms (115 V AC); 1.6 A rms (230 V AC); 3.7 A rms (100 V AC)
- Maximum Instantaneous Peak Current: 5.0 A pk (115 V AC); 2.5 A pk (230 V AC); 5.8 A pk (100 V AC)
- Inrush Current: < 9 A peak (115 V AC and 230 V AC)
- RMS NETWORK (OPTIONAL)
- Equipped with two-conductor twisted-pair network, reporting all operating parameters of amplifiers to system operator’s host computer.
- PHYSICAL
- Dimensions: W: 14.50 in (368 mm) x H: 22.40 in (569 mm) x D: 14.30 in (363 mm)
- Weight: 77 lb (34.93 kg)
- Enclosure: Premium multi-ply birch with slightly textured black finish
- Protective Grille: Powder-coated, hex-stamped steel with black mesh covering
- Rigging:
- Four ring and stud pan fittings, two on both top and bottom. Working load for each fitting is 420 lbs (190.51 kg), 1/5 the cabinet breaking strength (with straight tensile pull); 3/8 in or metric M10 nut plates optional
